Winsock not sending data sometimes, but it is others

I've had a topic like this before, and numerous Winsock problems. I feel like I know what I am doing, and clearly when something works once it shant work again! :(

Anywho, I've been doing some more progress on my project. Here are a couple of examples of working senddata:

Code:

---

Case "move"
                    For i = 0 To lstUsers.ListCount - 1
                        If lstUsers.List(i) = ParamData(0) Then
                            UserIndex = i
                            Exit For
                        End If
                    Next
                    lstX.List(UserIndex) = ParamData(1)
                    lstY.List(UserIndex) = ParamData(2)
                    lstAction.AddItem "move: " & ParamData(0) & " to " & ParamData(1) & "," & ParamData(2)
                    For i = ws.lbound To ws.Ubound
                        SendCommand "move", ParamData(0) & "," & ParamData(1) & "," & ParamData(2), i
                    Next i
                Case "chat"
                    lstChat.AddItem "[" & ParamData(0) & "] " & ParamData(1), 0
                    For i = ws.lbound To ws.Ubound
                        SendCommand "chat", ParamData(0) & "," & ParamData(1), i
                    Next i

---

Here is where I am having a problem:

Code:

---

Case "map"
                    If rsMysql.State = adStateOpen Then
                        rsMysql.Close
                    End If
                    MsgBox CommandData(0) & "," & CommandData(1)
                    rsMysql.Open "SELECT * FROM maps WHERE id = '" & CommandData(1) & "'", cnMysql, adOpenForwardOnly, adLockReadOnly, adCmdText
                    If rsMysql.RecordCount > 0 Then
                        Dim strMap As String, strTemp As String, curStep As Integer: strMap = rsMysql.Fields(2).Value & "end"
                        Do While Len(strMap) > 0
                            curStep = curStep + 1
                            If Len(strMap) < 100 Then
                                strTemp = strMap
                                strMap = Replace(strMap, strTemp, "")
                            Else
                                strTemp = Left$(strMap, 100)
                                strMap = Replace(strMap, strTemp, "")
                            End If
                            SendCommand "map", strTemp & "," & curStep, i
                        Loop
                    Else
                        SendCommand "map", "Error!", i
                    End If

---

My SendCommand function:

Code:

---

Private Sub SendCommand(sCommand As String, params As String, Index As Integer)
    If ws(Index).State = sckConnected Then
        ws(Index).SendData sCommand & "|" & params & "¶"
    End If
End Sub

---

The receiving end is not getting anything, and I have done lots of checking on this. After the senddata, I had an SendComplete sub put up a MsgBox when the data was sent. It worked for the first two cases I showed you, but with this case it did not show. Is there something simple I am just overlooking?

<3Your Winsock nub,

thejurm

My first suggestion in such cases is always the same: make sure you are using VB6 SP6.

The Winsock control was given many improvements over the years, especially in cases where multiple Winsocks are being used.

I am using the latest controls and have updated VB6 as far as I can

SendComplete does not mean everything was sent. When it occurs the Winsock control is saying "I have more room in my output buffer for another SendData call."

However if it is not happening that would seem to indicate that the other end is not taking its input. When the input buffer there fills up TCP will "push back" and prevent the sender from passing any more data over the wire.

Not getting SendComplete would seem to indicate that the receiver is very slow or hung.


Are you sure you have VB6 SP6? This still sounds like one of the problems fixed somewhere along the way from SP5 to SP6.

I'm attempting to update to SP6 again, but I keep getting the error that it did not install successfully? I am using the download from Microsoft's website

Alright, here's an update: Total reinstall, updated to SP6. Still having the same issue.

The receiving end, is it one of your programs ? maybe there is something wrong with that program ?

What would be wrong that makes it not receive the data on that end from one part only?

Bump, please help :)