I have been trying to make a LAN with the two computers in my house but I have a problem... Both adapters are sending data but neither of them are recieving anything! Could the problem be with the cable?
Thanks
Printable View
I have been trying to make a LAN with the two computers in my house but I have a problem... Both adapters are sending data but neither of them are recieving anything! Could the problem be with the cable?
Thanks
Do you have a hub or something in between the two? If you just have a cable running from one to the other then yes that is a problem. You can do it that way but only with a crossover cable which reverses the ends.
A simple way to check to see if your cable is ok is to see if the network lights on the back of your Network card are on. if so the cable is fine. if you are not using a hub then you definately need a crossover cable.
hope that helps
What are the computers os's? Have you got the workgroup set to the same thing on both computers?
Try this:
Goto Start > Run
Type Command
THen type ping 127.0.0.1
if you get replys then that means that the network card is working
do that on both computers
If ur on 98 make sure you get the updates because i've had problems with 98 and network cards seeing computers in Network Neighborhood with out the updates
And make sure, as said before, you have the right cables and they are working
by typing "ping 127.0.0.1" you'll get a reply regardless of whether the network card is working or not...:confused:
because it's a local loopback address, and will work on most computers if the TCP protocol has been installed properly. and if data is being sent then it probably is.
your right Walter, I meant TCP\IP and i forgot to tell him to ping the IP assigned to the network card.
The lights at the back of the cards go on, it is a crossover cable and after all there was nothing wrong with it. It was just the settings in the properties of the connection we had to fix. It is all working now. Thank you for all the replies :)
Did u assign a Static IP to the TCP/IP protocol? Unless y ou have a router u'll need to do this.
TO check if there is a IP address assigned do the following:
IN WIN98-ME:
START>RUN and type winipcfg
IN WIN 2000-XP(Both Versions)
START>RUN and type cmd
in the command promt type ipconfig
I didn't assign but we got different ones. We got it to work last friday afternoon. Then on monday we tried again and nothing happens! It says the cable is disconnected... No idea what is wrong! :(
Maybe the cable is shot.
Who knows! Or maybe one of the cards? :eek:Quote:
Originally posted by Admiral Michael
Maybe the cable is shot.
How about this.
PC 1
IP Address : 10.0.0.1
SubNet Mask : 255.255.255.0
PC 2
IP Address : 10.0.0.2
SubNet Mask : 255.255.255.0
Sorry, but what is this? :confused: :(Quote:
Originally posted by wrack
How about this.
PC 1
IP Address : 10.0.0.1
SubNet Mask : 255.255.255.0
PC 2
IP Address : 10.0.0.2
SubNet Mask : 255.255.255.0
Ohh my mistake. I should have been more clear.
Try using the IP addresses and subnet mask I gave here in both PC's and see if they are working. If not then try checking the cable. Simplest way to check a crossover cable is to put 1 end in a socket of a hub and the other end in another socket and if both lights are ON then it's all right else ur cable is dead.
After that u might want to check ur NIC.
Uh, how would I do that? I don't know much about this :(Quote:
Originally posted by wrack
Ohh my mistake. I should have been more clear.
Try using the IP addresses and subnet mask I gave here in both PC's and see if they are working. If not then try checking the cable. Simplest way to check a crossover cable is to put 1 end in a socket of a hub and the other end in another socket and if both lights are ON then it's all right else ur cable is dead.
After that u might want to check ur NIC.
You might have answered this but what operating system r u using?
Both WIN XP. Greek but I don't think that matters...Quote:
Originally posted by wrack
You might have answered this but what operating system r u using?
OK do u know how to assign IP address to an adaptor.Quote:
Originally posted by manavo11
Both WIN XP. Greek but I don't think that matters...
Open network connection.
Right click on Local Area Network
Click Property
Double click TCP/IP
DO not use Automatic Assign IP Address
There you can put IP Address
after that put the subnet mask
Same with another PC
After both is done, open system property and click on computer name tab and then click on change.
Make sure both the computer have same workgroup name or domain name. I guess u need to use workgroup name.
To make it easy just put MSHOME as a workgroup name in both and reboot.
Cheers.
Thanks. I'll try it as soon as I get a chance :)
No problems.
Hey wrack, I haven't tested it yet but I didn't quite understand what I am testing and looking for! What is the difference if I set specific IPs?
Thanks
If both the PC are in same workgroup then generally windows assigns them IP address automatically but if somehow it can't or doing something wrong then by assigning it manually you can be sure of that there is nothing wrong with IP addresses.
Cheers.
So if it doesn't work even by assigning my own IP addresses then I should assume that...
There is a problem with ur cable or hub/switch/rounter or NIC itself in any of the PC.Quote:
Originally posted by manavo11
So if it doesn't work even by assigning my own IP addresses then I should assume that...
Thanks again. Hopefully I will get a chance to check this shortly ;)
Hope you get success this time.;)Quote:
Originally posted by manavo11
Thanks again. Hopefully I will get a chance to check this shortly ;)
Me too :(Quote:
Originally posted by wrack
Hope you get success this time.;)
any luck?
I thought this was over...!!! ;)Quote:
Originally posted by Admiral Michael
any luck?
Well it isn't! lol
My friend works too much so we haven't even tried it yet! I wanted to try it with my computer and my father's but his computer is so f***ed up that without a format there is no hope... So I guess no luck :(